Fault 46 Safety option

Error: 46.1 (2E01hex \| 11777dec) Description: MOVISAFE® CS.. safety option no longer responding
	Response: Output stage inhibit
Cause	Measure
No synchronization could be performed with the safety option.	– When using a pluggable safety card, check the device assignment of the basic device and the safety card. – When using a pluggable safety card, check the slot and installation of the safety card. – Switch the device off and on again. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 46.1 (2E01hex | 11777dec)

Description: MOVISAFE® CS.. safety option no longer responding

Response: Output stage inhibit

Cause

Measure

No synchronization could be performed with the safety option.

– When using a pluggable safety card, check the device assignment of the basic device and the safety card.

– When using a pluggable safety card, check the slot and installation of the safety card.

– Switch the device off and on again.

– If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 46.2 (2E02hex \| 11778dec) Description: Invalid variant
	Response: Output stage inhibit
	Cause	Measure
	Safety option variant does not match inverter type.	Use the correct safety option variant.
	In the double axis of a MOVIDRIVE® modular application inverter, only safety cards without encoder interface may be used.	Use the correct safety card variant.

Error: 46.3 (2E03hex \| 11779dec) Description: MOVISAFE® CS.. safety option no longer responding
	Response: Output stage inhibit
	Cause	Measure
	Communication between inverter and safety option interrupted.	– When using a pluggable safety card, check the installation. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.
	The safety option has signaled a warning.	– When using a pluggable safety card, check the installation. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 46.50 (2E32hex \| 11826dec) Description: Warning
	Response: Warning with self-reset
Cause	Measure
The safety option has signaled a warning	Observe the warning of the safety option subcomponent. Identify the exact cause of this warning and take the appropriate measures for elimination.

Error: 46.50 (2E32hex | 11826dec)

Description: Warning

Response: Warning with self-reset

Cause

Measure

The safety option has signaled a warning

Observe the warning of the safety option subcomponent. Identify the exact cause of this warning and take the appropriate measures for elimination.

Error: 46.51 (2E33hex \| 11827dec) Description: Error
	Response: Emergency stop + output stage inhibit with self-reset
Cause	Measure
The safety option has detected an error.	Observe the fault code of the safety option subcomponent. Identify the exact cause of this fault message and take the appropriate measures to eliminate the fault.

Error: 46.51 (2E33hex | 11827dec)

Description: Error

Response: Emergency stop + output stage inhibit with self-reset

Cause

Measure

The safety option has detected an error.

Observe the fault code of the safety option subcomponent. Identify the exact cause of this fault message and take the appropriate measures to eliminate the fault.

Error: 46.52 (2E34hex \| 11828dec) Description: System error / data error / critical error
	Response: Output stage inhibit with self-reset
Cause	Measure
The MOVISAFE® CS.. safety option has detected an error.	Open the error status of the safety option in section Diagnostics -> MOVISAFE® CS... Determine the cause of the error from the error with the highest priority and perform the suggested troubleshooting measures.

Error: 46.52 (2E34hex | 11828dec)

Description: System error / data error / critical error

Response: Output stage inhibit with self-reset

Cause

Measure

The MOVISAFE® CS.. safety option has detected an error.

Open the error status of the safety option in section Diagnostics -> MOVISAFE® CS... Determine the cause of the error from the error with the highest priority and perform the suggested troubleshooting measures.