Fault 46 MOVISAFE^® CS..

Fault: 46.1 (2E01hex \| 11777dec) Description: MOVISAFE® CS.. safety option no longer responding
	Response: Output stage inhibit
Cause	Measure
No synchronization could be performed with the safety option.	– When using a pluggable safety card, check the device assignment of the basic device and the safety card. – When using a pluggable safety card, check the slot and installation of the safety card. – Switch the device off and on again. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Fault: 46.1 (2E01hex | 11777dec)

Description: MOVISAFE® CS.. safety option no longer responding

Response: Output stage inhibit

Cause

Measure

No synchronization could be performed with the safety option.

– When using a pluggable safety card, check the device assignment of the basic device and the safety card.

– When using a pluggable safety card, check the slot and installation of the safety card.

– Switch the device off and on again.

– If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Fault: 46.2 (2E02hex \| 11778dec) Description: Invalid variant
	Response: Output stage inhibit
	Cause	Measure
	Safety option variant does not match inverter type.	Use the correct safety option variant.
	In the double axis of a MOVIDRIVE® modular application inverter, only safety cards without encoder interface may be used.	Use the correct safety card variant.

Fault: 46.3 (2E03hex \| 11779dec) Description: MOVISAFE® CS.. safety option no longer responding
	Response: Output stage inhibit
	Cause	Measure
	Communication between inverter and safety option interrupted.	– When using a pluggable safety card, check the installation. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.
	The safety option has signaled a warning.	– When using a pluggable safety card, check the installation. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Fault: 46.50 (2E32hex \| 11826dec) Description: Warning
	Response: Warning with self-reset
Cause	Measure
The safety option has signaled a warning	Observe the warning of the safety option subcomponent. Identify the exact cause of this warning and take the appropriate measures for elimination.

Fault: 46.50 (2E32hex | 11826dec)

Description: Warning

Response: Warning with self-reset

Cause

Measure

The safety option has signaled a warning

Observe the warning of the safety option subcomponent. Identify the exact cause of this warning and take the appropriate measures for elimination.

Fault: 46.51 (2E33hex \| 11827dec) Description: Fault
	Response: Emergency stop + output stage inhibit with self-reset
Cause	Measure
The safety option has detected a fault.	Observe the fault code of the safety option subcomponent. Identify the exact cause of this fault message and take the appropriate measures to eliminate the fault.

Fault: 46.51 (2E33hex | 11827dec)

Description: Fault

Response: Emergency stop + output stage inhibit with self-reset

Cause

Measure

The safety option has detected a fault.

Observe the fault code of the safety option subcomponent. Identify the exact cause of this fault message and take the appropriate measures to eliminate the fault.

Fault: 46.52 (2E34hex \| 11828dec) Description: System fault / data fault / critical fault
	Response: Output stage inhibit with self-reset
Cause	Measure
The MOVISAFE® CS.. safety option has detected a fault.	Open the fault status of the safety option in section Diagnostics -> MOVISAFE® CS... Determine the cause of the fault from the fault with the highest priority and perform the suggested troubleshooting measures.

Fault: 46.52 (2E34hex | 11828dec)

Description: System fault / data fault / critical fault

Response: Output stage inhibit with self-reset

Cause

Measure

The MOVISAFE® CS.. safety option has detected a fault.

Open the fault status of the safety option in section Diagnostics -> MOVISAFE® CS... Determine the cause of the fault from the fault with the highest priority and perform the suggested troubleshooting measures.

Fault 46 MOVISAFE® CS..

Fault 46 MOVISAFE^® CS..