Fieldbus interface

Fieldbus configuration

Activating fieldbus connection

Activate fieldbus connection and show further setting fields for configuring the fieldbus connection.

Index: 50000.150

IEC name: –

Start address

Start address of the fieldbus process data words in the array of the bus system. Counting starts at 1

Index: 50000.151

IEC name: –

Basic process data

Amount of process data for the software module without activated "Optional process data"

Index: 50000.159

IEC name: –

Optional process data

Additional process data due to the activated "Optional process data"

Index: –

IEC name: –

Additional process data

Additional process data that is not occupied by the software module and can be freely assigned by the user. The assignment of these process data must be programmed in the IEC program.

Index: 50000.160

IEC name: –

Process data length

Length of the process data of the software module

Index: –

IEC name: –

Optional process data – see process output data and process input data

Control word/status word 2

Selection of the balancing priority

Index: 50000.167

IEC name: –

Tension between axis group member 1 and 2

Specification of a tension between axis group members 1 and 2, for example when reaching the target.

Index: 50000.168

IEC name: –

Load distribution

Specification of a load distribution between axis group members 1 to 4. When using load distribution, a ratio not equal to 0:0 must be transferred.

Index: 50000.169

IEC name: –

Position controller P gain

Specification of the P gain of the position controller if it is to be changed during operation.

Index: 50000.170

IEC name: –

Balance controller P gain

Specification of the P gain of the balance controller if it is to be changed during operation. This is possible with the setting "Torque" and "Skew" for "Balancing priority".

Index: 50000.171

IEC name: –

User-defined speed correction values

Specification of own speed correction values with the setting "User-defined speed correction values" or "User-defined speed correction values with diagnostics" for "Balancing priority".

Index: 50000.172

IEC name: –

Skew offset

Specification of a symmetrical skew offset with the setting "Skew" and "Skew without overload monitor" for the "Balancing priority" for consciously skewing individual axis group members to each other.

Index: 50000.173

IEC name: –

Anti-sway control

Display the additional optional process data for the "Anti-sway control" function.

Index: 50000.174

IEC name: –

Status word/control word

INFORMATION: Only visible when the optional anti-sway control process data word is activated.

Activation and deactivation of anti-sway control and feedback whether it is still busy.

Index: 50000.175

IEC name: –

Payload mass

INFORMATION: Only visible when the optional anti-sway control process data word is activated.

Order-related modification of the payload configuration

Index: 50000.176

IEC name: –

Distance between lifting and traveling trolley

INFORMATION: Only visible when the optional anti-sway control process data word is activated.

Order-related change to the configuration of the distance between lifting and traveling trolley

Index: 50000.177

IEC name: –

Deflection of the oscillation

INFORMATION: Only visible when the optional anti-sway control process data word is activated.

Specification of deflection of the oscillation (in preparation)

Index: 50000.178

IEC name: –

Number of axis group members of the MultiAxisController

Specification of the number of axis group members of the software module to obtain additional actual values of the axis group members on the fieldbus interface.

Index: 50000.153

IEC name: –

Access control

Control access via fieldbus. This makes it possible to move the software module separately if the MOVIKIT^® MultiAxisController or Robotics is located at a higher level.

Index: 50000.185

IEC name: –

Decimal places via fieldbus

Define the number of decimal places for position, speed, acceleration, and jerk via fieldbus.

Index: 50000.155 (position), 50000.156 (speed), 50000.157 (acceleration), 50000.158 (jerk)

Advanced settings

Move the "Deactivate external encoders" bit from PO 10 to PO 1

With this setting, the "Deactivate external encoders" bit can be moved from control word PO 10 bit 13/status word PI 10 bit 13 to control word PO 1 bit 10/status word PI 1 bit 10.

Index: 50000.184

IEC name: –

PROFINET diagnostic alarms

Activate diagnostic alarms

INFORMATION: A current device description file must be available for the texts to be displayed correctly.

Send errors and warnings as PROFINET diagnostic alarms so that they can be read in plain text.

Index: 50000.164

IEC name: –

Slot number

Position of the software module on the fieldbus. Slot number 1 corresponds to the first freely available slot.

For more information, refer to the "Controllers of the MOVI-C^® Modular Automation System – Startup with PROFINET/PROFIsafe" manual.

Index: –

IEC name: –