Fault 63 Speed-dependent drive safety function
Fault: 63.1 (3F01hex | 16129dec) Description: SLS 1 limit speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 1 exceeded in positive direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (limit speed SLS 1), and adjust if necessary. | |
Fault: 63.2 (3F02hex | 16130dec) Description: SLS 2 limit speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 2 exceeded in positive direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (limit speed SLS 2), and adjust if necessary. | |
Fault: 63.3 (3F03hex | 16131dec) Description: SLS 3 limit speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 3 exceeded in positive direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (limit speed SLS 3), and adjust if necessary. | |
Fault: 63.4 (3F04hex | 16132dec) Description: SLS 4 limit speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 4 exceeded in positive direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the limit speed of the safety card (limit speed SLS 4), and adjust if necessary. | |
Fault: 63.5 (3F05hex | 16133dec) Description: SLS 1 limit speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 1 exceeded in negative direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (limit speed SLS 1), and adjust if necessary. | |
Fault: 63.6 (3F06hex | 16134dec) Description: SLS 2 limit speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 2 exceeded in negative direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (limit speed SLS 2), and adjust if necessary. | |
Fault: 63.7 (3F07hex | 16135dec) Description: SLS 3 limit speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 3 exceeded in negative direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (limit speed SLS 3), and adjust if necessary. | |
Fault: 63.8 (3F08hex | 16136dec) Description: SLS 4 limit speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 4 exceeded in negative direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (limit speed SLS 4), and adjust if necessary. | |
Fault: 63.9 (3F09hex | 16137dec) Description: SLS maximum speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Maximum speed SLS exceeded in positive direction of movement during monitoring delay. | – Check the maximum speed of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (maximum speed), and adjust if necessary. | |
Fault: 63.13 (3F0Dhex | 16141dec) Description: SLS maximum speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Maximum speed SLS exceeded in negative direction of movement during monitoring delay. | – Check the maximum speed of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (maximum speed), and adjust if necessary. | |
Fault: 63.17 (3F11hex | 16145dec) Description: SLS 1 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 1 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SLS 1, jerk time SLS 1, ramp type SLS 1), and adjust if necessary. | |
Fault: 63.18 (3F12hex | 16146dec) Description: SLS 2 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 2 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SLS 2, jerk time SLS 2, ramp type SLS 2), and adjust if necessary. | |
Fault: 63.19 (3F13hex | 16147dec) Description: SLS 3 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 3 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SLS 3, jerk time SLS 3, ramp type SLS 3), and adjust if necessary. | |
Fault: 63.20 (3F14hex | 16148dec) Description: SLS 4 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 4 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SLS 4, jerk time SLS 4, ramp type SLS 4), and adjust if necessary. | |
Fault: 63.21 (3F15hex | 16149dec) Description: SLS 1 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 1 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SLS 1, jerk time SLS 1, ramp type SLS 1), and adjust if necessary. | |
Fault: 63.22 (3F16hex | 16150dec) Description: SLS 2 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 2 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SLS 2, jerk time SLS 2, ramp type SLS 2), and adjust if necessary. | |
Fault: 63.23 (3F17hex | 16151dec) Description: SLS 3 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 3 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SLS 3, jerk time SLS 3, ramp type SLS 3), and adjust if necessary. | |
Fault: 63.24 (3F18hex | 16152dec) Description: SLS 4 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SLS 4 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SLS 4, jerk time SLS 4, ramp type SLS 4), and adjust if necessary. | |
Fault: 63.25 (3F19hex | 16153dec) Description: SSM 1 limit speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSM 1 exceeded in positive direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the limit speed of the safety card (limit speed SSM 1), and adjust if necessary. | |
Fault: 63.26 (3F1Ahex | 16154dec) Description: SSM 2 limit speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSM 2 exceeded in positive direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the limit speed of the safety card (limit speed SSM 2), and adjust if necessary. | |
Fault: 63.27 (3F1Bhex | 16155dec) Description: SSM 3 limit speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSM 3 exceeded in positive direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the limit speed of the safety card (limit speed SSM 3), and adjust if necessary. | |
Fault: 63.28 (3F1Chex | 16156dec) Description: SSM 4 limit speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSM 4 exceeded in positive direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the limit speed of the safety card (limit speed SSM 4), and adjust if necessary. | |
Fault: 63.29 (3F1Dhex | 16157dec) Description: SSM 1 limit speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSM 1 exceeded in negative direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the limit speed of the safety card (limit speed SSM 1), and adjust if necessary. | |
Fault: 63.30 (3F1Ehex | 16158dec) Description: SSM 2 limit speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSM 2 exceeded in negative direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the limit speed of the safety card (limit speed SSM 2), and adjust if necessary. | |
Fault: 63.31 (3F1Fhex | 16159dec) Description: SSM 3 limit speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSM 3 exceeded in negative direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the limit speed of the safety card (limit speed SSM 3), and adjust if necessary. | |
Fault: 63.32 (3F20hex | 16160dec) Description: SSM 4 limit speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSM 4 exceeded in negative direction of movement. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the limit speed of the safety card (limit speed SSM 4), and adjust if necessary. | |
Fault: 63.33 (3F21hex | 16161dec) Description: SSx maximum speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Maximum speed SSx exceeded in positive direction of movement during monitoring delay. | – Check the maximum speed of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (maximum speed), and adjust if necessary. | |
Fault: 63.41 (3F29hex | 16169dec) Description: SSx maximum speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Maximum speed SSx exceeded in negative direction of movement during monitoring delay. | – Check the maximum speed of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (maximum speed), and adjust if necessary. | |
Fault: 63.49 (3F31hex | 16177dec) Description: SSx 1 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 1 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 1, jerk time SSx 1, ramp type SSx 1), and adjust if necessary. | |
Fault: 63.50 (3F32hex | 16178dec) Description: SSx 2 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 2 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 2, jerk time SSx 2, ramp type SSx 2), and adjust if necessary. | |
Fault: 63.51 (3F33hex | 16179dec) Description: SSx 3 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 3 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 3, jerk time SSx 3, ramp type SSx 3), and adjust if necessary. | |
Fault: 63.52 (3F34hex | 16180dec) Description: SSx 4 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 4 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 4, jerk time SSx 4, ramp type SSx 4), and adjust if necessary. | |
Fault: 63.53 (3F35hex | 16181dec) Description: SSx 5 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 5 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 5, jerk time SSx 5, ramp type SSx 5), and adjust if necessary. | |
Fault: 63.54 (3F36hex | 16182dec) Description: SSx 6 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 6 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 6, jerk time SSx 6, ramp type SSx 6), and adjust if necessary. | |
Fault: 63.55 (3F37hex | 16183dec) Description: SSx 7 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 7 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 7, jerk time SSx 7, ramp type SSx 7), and adjust if necessary. | |
Fault: 63.56 (3F38hex | 16184dec) Description: SSx 8 limit speed exceeded in positive direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 8 exceeded in positive direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 8, jerk time SSx 8, ramp type SSx 8), and adjust if necessary. | |
Fault: 63.57 (3F39hex | 16185dec) Description: SSx 1 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 1 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 1, jerk time SSx 1, ramp type SSx 1), and adjust if necessary. | |
Fault: 63.58 (3F3Ahex | 16186dec) Description: SSx 2 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 2 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 2, jerk time SSx 2, ramp type SSx 2), and adjust if necessary. | |
Fault: 63.59 (3F3Bhex | 16187dec) Description: SSx 3 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 3 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 3, jerk time SSx 3, ramp type SSx 3), and adjust if necessary. | |
Fault: 63.60 (3F3Chex | 16188dec) Description: SSx 4 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 4 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 4, jerk time SSx 4, ramp type SSx 4), and adjust if necessary. | |
Fault: 63.61 (3F3Dhex | 16189dec) Description: SSx 5 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 5 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 5, jerk time SSx 5, ramp type SSx 5), and adjust if necessary. | |
Fault: 63.62 (3F3Ehex | 16190dec) Description: SSx 6 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 6 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 6, jerk time SSx 6, ramp type SSx 6), and adjust if necessary. | |
Fault: 63.63 (3F3Fhex | 16191dec) Description: SSx 7 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 7 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 7, jerk time SSx 7, ramp type SSx 7), and adjust if necessary. | |
Fault: 63.64 (3F40hex | 16192dec) Description: SSx 8 limit speed exceeded in negative direction of movement during deceleration | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Limit speed SSx 8 exceeded in negative direction of movement during deceleration. | – Check deceleration, jerk time, and ramp type of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (deceleration SSx 8, jerk time SSx 8, ramp type SSx 8), and adjust if necessary. | |
Fault: 63.65 (3F41hex | 16193dec) Description: SSR 1 upper limit speed exceeded | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Upper limit speed SSR 1 exceeded. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (upper limit speed SSR 1), and adjust if necessary. | |
Fault: 63.66 (3F42hex | 16194dec) Description: SSR 2 upper limit speed exceeded | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Upper limit speed SSR 2 exceeded. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (upper limit speed SSR 2), and adjust if necessary. | |
Fault: 63.67 (3F43hex | 16195dec) Description: SSR 3 upper limit speed exceeded | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Upper limit speed SSR 3 exceeded. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (upper limit speed SSR 3), and adjust if necessary. | |
Fault: 63.68 (3F44hex | 16196dec) Description: SSR 4 upper limit speed exceeded | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Upper limit speed SSR 4 exceeded. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (upper limit speed SSR 4), and adjust if necessary. | |
Fault: 63.69 (3F45hex | 16197dec) Description: SSR 1 lower limit speed exceeded | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Lower limit speed SSR 1 exceeded. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (lower limit speed SSR 1), and adjust if necessary. | |
Fault: 63.70 (3F46hex | 16198dec) Description: SSR 2 lower limit speed exceeded | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Lower limit speed SSR 2 exceeded. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (lower limit speed SSR 2), and adjust if necessary. | |
Fault: 63.71 (3F47hex | 16199dec) Description: SSR 3 lower limit speed exceeded | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Lower limit speed SSR 3 exceeded. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (lower limit speed SSR 3), and adjust if necessary. | |
Fault: 63.72 (3F48hex | 16200dec) Description: SSR 4 lower limit speed exceeded | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Lower limit speed SSR 4 exceeded. | – Check the speed setpoint of the application with the drive safety function active, and adjust if necessary. – Check the parameterization of the safety card (lower limit speed SSR 4), and adjust if necessary. | |
Fault: 63.73 (3F49hex | 16201dec) Description: SSR maximum speed exceeded in positive direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Maximum speed SSR exceeded in positive direction of movement during monitoring delay. | – Check the maximum speed of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (maximum speed), and adjust if necessary. | |
Fault: 63.74 (3F4Ahex | 16202dec) Description: SSR maximum speed exceeded in negative direction of movement | ||
|---|---|---|
| Response: FS – warning | |
Cause | Measure | |
Maximum speed SSR exceeded in negative direction of movement during monitoring delay. | – Check the maximum speed of the application while the drive safety function is active, and adjust if necessary. – Check the parameterization of the safety card (maximum speed), and adjust if necessary. | |
