Error 150 Controller firmware – General device fault

Error: 150.1 (9601hex \| 38401dec) Description: Unknown error

Cause	Measure
The firmware of the MOVI-C® CONTROLLER has detected a serious fault that cannot be assigned to an exact device fault.	– Activate the function to store the logbooks in the MOVI-C® CONTROLLER file system. Check the entries with the severity "Fault" or "Exception" in the logbooks for further information. – Acknowledge the fault. The MOVI-C® CONTROLLER is restarted. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 150.1 (9601hex | 38401dec)

Description: Unknown error

Cause

Measure

The firmware of the MOVI-C® CONTROLLER has detected a serious fault that cannot be assigned to an exact device fault.

– Activate the function to store the logbooks in the MOVI-C® CONTROLLER file system. Check the entries with the severity "Fault" or "Exception" in the logbooks for further information.

– Acknowledge the fault. The MOVI-C® CONTROLLER is restarted.

– If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 150.2 (9602hex \| 38402dec) Description: Restart after exception handling

Cause	Measure
The MOVI-C® CONTROLLER has performed exception handling due to unauthorized access to the memory with subsequent restart.	– Activate the function to store the logbooks in the MOVI-C® CONTROLLER file system. Check the entries with the severity "Fault" or "Exception" in the logbooks for further information. – Acknowledge the fault. The MOVI-C® CONTROLLER is restarted. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 150.2 (9602hex | 38402dec)

Description: Restart after exception handling

Cause

Measure

The MOVI-C® CONTROLLER has performed exception handling due to unauthorized access to the memory with subsequent restart.

– Activate the function to store the logbooks in the MOVI-C® CONTROLLER file system. Check the entries with the severity "Fault" or "Exception" in the logbooks for further information.

– Acknowledge the fault. The MOVI-C® CONTROLLER is restarted.

– If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 150.3 (9603hex \| 38403dec) Description: Faulty booting phase

Cause	Measure
The MOVI-C® CONTROLLER could not start properly. The configuration of the firmware of the MOVI-C® CONTROLLER is incorrect or corrupt.	– Activate the function to store the logbooks in the MOVI-C® CONTROLLER file system. Check the entries with the severity "Fault" or "Exception" in the logbooks for further information. – Acknowledge the fault. The MOVI-C® CONTROLLER is restarted. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 150.3 (9603hex | 38403dec)

Description: Faulty booting phase

Cause

Measure

The MOVI-C® CONTROLLER could not start properly. The configuration of the firmware of the MOVI-C® CONTROLLER is incorrect or corrupt.

– Activate the function to store the logbooks in the MOVI-C® CONTROLLER file system. Check the entries with the severity "Fault" or "Exception" in the logbooks for further information.

– Acknowledge the fault. The MOVI-C® CONTROLLER is restarted.

– If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 150.4 (9604hex \| 38404dec) Description: Error in early booting phase

Cause	Measure
The MOVI-C® CONTROLLER could not start properly due to errors in the early booting phase.	– Activate the function to store the logbooks in the MOVI-C® CONTROLLER file system. Check the entries with the severity "Fault" or "Exception" in the logbooks for further information. – If the software packages are corrupt, load original SEW-EURODRIVE software packages onto the removable storage device again. – Acknowledge the fault. The MOVI-C® CONTROLLER is restarted. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Error: 150.4 (9604hex | 38404dec)

Description: Error in early booting phase

Cause

Measure

The MOVI-C® CONTROLLER could not start properly due to errors in the early booting phase.

– Activate the function to store the logbooks in the MOVI-C® CONTROLLER file system. Check the entries with the severity "Fault" or "Exception" in the logbooks for further information.

– If the software packages are corrupt, load original SEW-EURODRIVE software packages onto the removable storage device again.

– Acknowledge the fault. The MOVI-C® CONTROLLER is restarted.

– If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.