Fault 32 Communication

Fault: 32.1 (2001hex \| 8193dec) Description: CBus communication timeout

Cause	Measure
A timeout occurred in the process data transfer during communication via the CBus communication option.	– Check the wiring of the system bus. – Make sure that the communication option is set correctly. – Check the set timeout time of the CBus communication option.

Fault: 32.1 (2001hex | 8193dec)

Description: CBus communication timeout

Cause

Measure

A timeout occurred in the process data transfer during communication via the CBus communication option.

– Check the wiring of the system bus.

– Make sure that the communication option is set correctly.

– Check the set timeout time of the CBus communication option.

Fault: 32.2 (2002hex \| 8194dec) Description: EtherCAT®/SBusPLUS communication timeout

Cause	Measure
Timeout in process data transfer during EtherCAT®/SBusPLUS communication.	– Check the wiring of system bus and module bus. – Make sure that the EtherCAT®/SBusPLUS configuration in the controller is set correctly. – Check the set timeout time of the EtherCAT®/SBusPLUS interface.

Fault: 32.2 (2002hex | 8194dec)

Description: EtherCAT®/SBusPLUS communication timeout

Cause

Measure

Timeout in process data transfer during EtherCAT®/SBusPLUS communication.

– Check the wiring of system bus and module bus.

– Make sure that the EtherCAT®/SBusPLUS configuration in the controller is set correctly.

– Check the set timeout time of the EtherCAT®/SBusPLUS interface.

Fault: 32.3 (2003hex \| 8195dec) Description: Faulty synchronization signal

Cause	Measure
Synchronization signal period is not correct.	Make sure that the EtherCAT®/SBusPLUS configuration in the controller is set correctly.

Fault: 32.3 (2003hex | 8195dec)

Description: Faulty synchronization signal

Cause

Measure

Synchronization signal period is not correct.

Make sure that the EtherCAT®/SBusPLUS configuration in the controller is set correctly.

Fault: 32.4 (2004hex \| 8196dec) Description: Missing synchronization signal

Cause	Measure
No synchronization signal present.	Make sure that the EtherCAT®/SBusPLUS configuration in the controller is set correctly.

Fault: 32.4 (2004hex | 8196dec)

Description: Missing synchronization signal

Cause

Measure

No synchronization signal present.

Make sure that the EtherCAT®/SBusPLUS configuration in the controller is set correctly.

Fault: 32.5 (2005hex \| 8197dec) Description: Synchronization timeout

Cause	Measure
Timeout while synchronizing to synchronization signal.	Make sure that the EtherCAT®/SBusPLUS configuration in the controller is set correctly.

Fault: 32.5 (2005hex | 8197dec)

Description: Synchronization timeout

Cause

Measure

Timeout while synchronizing to synchronization signal.

Make sure that the EtherCAT®/SBusPLUS configuration in the controller is set correctly.

Fault: 32.6 (2006hex \| 8198dec) Description: Error while transferring parameter set

Cause	Measure
Error while downloading parameter set to device.	– Check the wiring of system bus and module bus. – Restart the transfer.

Fault: 32.6 (2006hex | 8198dec)

Description: Error while transferring parameter set

Cause

Measure

Error while downloading parameter set to device.

– Check the wiring of system bus and module bus.

– Restart the transfer.

Fault: 32.7 (2007hex \| 8199dec) Description: Application heartbeat timeout

Cause	Measure
Communication between the application program (e.g. IEC program or MOVIKIT® from the Drive category) and the device was interrupted.	– Check the status of the application program. – Restart the application program.

Fault: 32.7 (2007hex | 8199dec)

Description: Application heartbeat timeout

Cause

Measure

Communication between the application program (e.g. IEC program or MOVIKIT® from the Drive category) and the device was interrupted.

– Check the status of the application program.

– Restart the application program.

Fault: 32.8 (2008hex \| 8200dec) Description: User-timeout timeout

Cause	Measure
The timeout time of the user timeout function has expired.	– Check communication. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Fault: 32.8 (2008hex | 8200dec)

Description: User-timeout timeout

Cause

Measure

The timeout time of the user timeout function has expired.

– Check communication.

– If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Fault: 32.11 (200Bhex \| 8203dec) Description: Local mode timeout

	Cause	Measure
	Communication connection to device interrupted in local mode.	Increase the timeout setting in local mode.
	New Scope project created.	– Reset the fault. – Start local mode again.
	Scope measurement loaded from device.	– Reset the fault. – Start local mode again.

Fault: 32.12 (200Chex \| 8204dec) Description: Manual mode timeout

	Cause	Measure
	Communication connection to inverter interrupted in manual mode.	– Check whether too many programs are open on the engineering PC. – Increase the timeout time in manual mode.
	New Scope project created.	– Acknowledge the fault. – Restart manual mode.
	Scope measurement transferred from inverter to project.	– Acknowledge the fault. – Restart manual mode.

Fault: 32.13 (200Dhex \| 8205dec) Description: Process data timeout

Cause	Measure
Timeout in the process data transfer.	– Switch the devices off and on again. – If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Fault: 32.13 (200Dhex | 8205dec)

Description: Process data timeout

Cause

Measure

Timeout in the process data transfer.

– Switch the devices off and on again.

– If the fault occurs repeatedly, contact SEW‑EURODRIVE Service.

Fault: 32.14 (200Ehex \| 8206dec) Description: Internal communication error

Cause	Measure
An error occurred in internal communication.	– Switch the device off and on again. – If the fault occurs repeatedly, replace the safety option and send it together with the fault number to SEW‑EURODRIVE. For further support, contact SEW‑EURODRIVE Service.

Fault: 32.14 (200Ehex | 8206dec)

Description: Internal communication error

Cause

Measure

An error occurred in internal communication.

– Switch the device off and on again.

– If the fault occurs repeatedly, replace the safety option and send it together with the fault number to SEW‑EURODRIVE. For further support, contact SEW‑EURODRIVE Service.

Fault: 32.15 (200Fhex \| 8207dec) Description: Error due to configuration change

Cause	Measure
The CAN interface setting has been changed.	Acknowledge the fault and restart the firmware.

Fault: 32.15 (200Fhex | 8207dec)

Description: Error due to configuration change

Cause

Measure

The CAN interface setting has been changed.

Acknowledge the fault and restart the firmware.

Fault: 32.16 (2010hex \| 8208dec) Description: CBus PE data timeout

Cause	Measure
One or more stations on the CBus no longer respond.	– Check CBus cabling. – Check whether CBus axis group members are switched on.

Fault: 32.16 (2010hex | 8208dec)

Description: CBus PE data timeout

Cause

Measure

One or more stations on the CBus no longer respond.

– Check CBus cabling.

– Check whether CBus axis group members are switched on.